Full Builder Gel Starter Kit ***SAVE from R244**

Getting started with Builder Gel? This is ALL you need to create stunning overlays or full sculptured nails.
Simplest system, best quality. No primers, no bonders, NO anything else!

***SAVE from R177*** on Full Starter Kit PLUS 5% on any additional colours added to the basic kit

Kit includes:

1 x Clear Builder Gel, 1 x Blushing Bride Builder Gel, 1 x Dare To Bare Builder Gel, 1 x Gel Polish Base Coat, 1 x Gel Polish Top Coat, 1 x Cuticle Oil, 3 x Half Moon File, 1 x Buffer Block, 20 x tips, 1 x Nail Glue, 1 x Gel Brush, 100 x lint free nail wipes, 1 x Microfibre Cosmetic Bag 

If you need extra colours, simply tick the box next to the products you want to add to the basic kit.

In stock

SKU
NBG-STARTER

Starting From R980.00

To R2,556.75

Customize Full Builder Gel Starter Kit ***SAVE from R244**

* Required Fields

Your Customization
Full Builder Gel Starter Kit ***SAVE from R244**
Full Builder Gel Starter Kit ***SAVE from R244**

In stock

R980.00

Summary

    Getting started with Builder Gel?  This is ALL you need to create a stunning French Manicure.

    Simplest system, best quality.  No primers, no bonders, NO anything else! 

    This kit includes:

    1 x Clear Builder Gel

    1 x Blushing Bride Builder Gel

    1 x Dare To Bare Builder Gel 

    1 x Base Coat

    1 x Top Coat

    1 x Cuticle Oil

    3 x Half Moon File

    1 x Buffer Block

    20 x tips

    1 x Nail Glue

    1 x Gel Brush

    100 x lint free nail wipes

    1 x Microfibre Cosmetic Bag

     

    More Information
    SKU NBG-STARTER
    Write Your Own Review
    You're reviewing:Full Builder Gel Starter Kit ***SAVE from R244**
    Your Rating
    Ask Your Question
    Jot us a note and we’ll get back to you as quickly as possible.

    STEP-BY-STEP 

    1. Prepare the nails, apply tips (if using tips) and remove the shine from the tip with a buffer block.

    2. Remove all debris and dust with a dusting brush and wipe with sanitiser.

    3. Apply a very thin layer of CRYSTAL CLAWZ Base Gel from cuticle to free edge, covering the entire nail. Cure for 30 seconds LED or 2 Min UV.

    4. Pick up a large bead of Crystal Clawz Builder Gel. Slowly set it down in the centre of the cuticle area about 5-6mm away from the cuticles. DON’T apply any pressure yet, you are NOT going to brush this gel on. You are going to allow it to freely drop or drizzle off of your brush (as if icing a cake). Start to apply pressure near the free edge (end of nail) to tail off the log of gel. Don’t panic! It will look
      ridiculous. Allow time for it to self level.

    5. Allow to self-level

    6. Using a detail liner brush, spread the gel to the cuticles and sidewalls, making sure that you do not get the product on the skin or cuticles.  If this happens, clean off skin and cuticles before curing as this can cause lifting of the product.

    7. The client’s hand can be turned upside down to allow the gel to run back to the apex if it has levelled down too much.  

    8. Make sure you have an even arch (apex) from the cuticle to the end of the nail, and then from side to side (the C-Curve)

    9. Cure under LED lamp for 60 seconds (approx. 3 minutes under a UV lamp)

      *HEAT SPIKE WARNING* All hard Gels (Builder and Rubber Base) will heat up as a result of the chemical reaction in the curing process.  If the client experiences a burning sensation, remove the hand from the lamp, wait a few seconds and reinsert.  This will NOT damage the nail it will only cause discomfort.  The tolerance level will differ between clients

    10. File to desired length and shape; ensuring that the end product is smooth and thin, without any bumps.  Check that you have an even arch (apex) from the cuticle to the end of the nail, and then from side to side (this is called the C-Curve).  Remember – the overlay needs to be thinner at the front and the cuticle.  The edge should be no thicker than a credit card and the cuticle area should be thin enough to blend with the natural nail.

    11. Use Buffer block and buff to smooth the surface.

    12. Remove all dust using your dusting brush and wipe nail using a lint free cotton wipe and sanitiser.

    13. Finish with desired CRYSTAL CLAWZ Top Coat, or apply colour/art before applying Top Coat
    Frequently Bought Together